Knowing Essential Plumbing Skills is Important When Installing a Bathtub
Knowing Essential Plumbing Skills is Important When Installing a Bathtub
Blog Article
They are making several great annotation related to How to Install a Bathtub Yourself overall in the article which follows.
Mounting a bath tub isn't specifically rocket science, but it does need solid plumbing, carpentry, as well as often, tiling skills. Replacing an old tub with a new one is additionally a moderately challenging project. If the old tub is readily accessible, the project can relocate quickly; if you need to open a wall to get rid of the old bathtub and also position the brand-new bathtub, the job is much harder. In either instance, the project is within a residence handyman's abilities, although you will certainly need an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually certified yourself for the work as well as are comfortable attempting it. Rather than working with a contractor to take control of a halfway-completed job, it is far better to take into consideration using one before you start. Possibilities are you may need a specialist plumber to make tube links.
This short article will certainly assist you mount a new bath tub in your bathroom if you have actually already bought a new tub and don't require to alter the plan of your previous water supply pipelines.
Your tools and material list ought to comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted access that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Prior to going on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end provides a connection to the current supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet and the sink. Protect the tap in position with the producer given backnut. Once the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous type needs to be linked to the faucet finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Using both wooden boards under its feet, position the bathtub in the required placement. The wood boards are useful in equally spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to make sure that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the bathtub up until the level reviews degree.
To set up taps, fit all-time low of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the water and inspect all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub and likewise inspect the overflow outlet and the regular outlet for leakages.
Finally, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and sealing around the bath tub needs to wait till the bathtub has been used at the very least when as this will certainly settle it right into its final position.
Preparing for the Installation
First of all, the supporting framework provided with the bathroom should be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps system to avoid stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last setting.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to break an inflexible seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, leading to problems with moisture and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in usage. The sealer can split fairly early if you do not take into account this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly readily available on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very curious about How to Install a Bathtub and I hope you appreciated our blog post. In case you liked our post please be sure to pass it around. Thanks a bunch for your time. Come back soon.
Quick, reliable, call! Report this page